MSB Posted November 2, 2020 Author Share Posted November 2, 2020 If you have s5, try setting up your prop as I suggested and export it as a visualizer file for use in s4. I don't have access to s4 anymore to try that. Greg Link to comment Share on other sites More sharing options...
pouney91 Posted November 3, 2020 Share Posted November 3, 2020 bonjour greg j ai le s5 instaler sur un autre ordinateur mais je n ai pas tout compris dans le s5 je n'arrive pas a trouver comment mettre mon pixie 16 dedans le s5 est quand meme bien différent du s4 dur dur de s'abituer a mon age mais je vais essayer donc il faut que je fasse une séquence musical avec le séquencer s5 et ensuite l'enregister dans le visualiseur pour pouvoir la transférer dans le s4 sauf que le s4 ne prend pas en charge les fichiers loredit j'essaye et je vous tient au courant laisser moi quelque jours j ai commencer a installer mon sectacle merci de m'aider cordialement hello greg I have the s5 installed on another computer but i didn't understand everything in the s5 i cant figure out how to put my pixie 16 in it the s5 is still very different from the s4 hard to get used to my age but I will try so I have to make a musical sequence with the s5 sequencer and then save it in the viewer to be able to transfer it to the s4 except that the s4 does not support loredit files I try and I keep you posted leave me a few days I started to install my sectacle thank you for helping me cordially Link to comment Share on other sites More sharing options...
dibblejr Posted November 3, 2020 Share Posted November 3, 2020 9 hours ago, pouney91 said: bonjour greg j ai le s5 instaler sur un autre ordinateur mais je n ai pas tout compris dans le s5 je n'arrive pas a trouver comment mettre mon pixie 16 dedans le s5 est quand meme bien différent du s4 dur dur de s'abituer a mon age mais je vais essayer donc il faut que je fasse une séquence musical avec le séquencer s5 et ensuite l'enregister dans le visualiseur pour pouvoir la transférer dans le s4 sauf que le s4 ne prend pas en charge les fichiers loredit j'essaye et je vous tient au courant laisser moi quelque jours j ai commencer a installer mon sectacle merci de m'aider cordialement hello greg I have the s5 installed on another computer but i didn't understand everything in the s5 i cant figure out how to put my pixie 16 in it the s5 is still very different from the s4 hard to get used to my age but I will try so I have to make a musical sequence with the s5 sequencer and then save it in the viewer to be able to transfer it to the s4 except that the s4 does not support loredit files I try and I keep you posted leave me a few days I started to install my sectacle thank you for helping me cordially As far as i know, you cannot use an S5 prop file in S4 Vis. I find the S4 vis much easier to use - for some reason. I guess thats where my roots are planted. You can export a loredit file in the new versions of S5. open s5 sequence, under File, export as LMS However if the sequence contains ME rows, it will not export the ME rows. Personally I tested the export to LMS between my two computers and the sequence did not look like it was sup to. This may have been fixed by now though. Best of luck JR Link to comment Share on other sites More sharing options...
pouney91 Posted November 10, 2020 Share Posted November 10, 2020 bonjour je reviens vers vous je pense que pour passer mes cordes a 100 leds je me trompe aussi Ces cavaliers remplaceront ceux paramètres réglables par Hardware Utility. Sauteur 1 est le plus proche de l'extrémité étiquetée JP5. Jumper Ce qu'il fait J1 WS28118, BRG, 50 pixels J2 WS2801, RVB, 50 pixels J3 WS28118, RVB, 100 pixels L'utilitaire matériel est utilisé pour configurer la mise sous tension configuration du contrôleur. Des paramètres configuré ci-dessous, seule la résolution logique / l'état de basculement peut être modifiée à la volée en séquences, et uniquement en mode de compatibilité CCR. Tous les autres les paramètres sont définis par et ne peuvent être modifiés que par l'utilitaire matériel. Cliquez sur le bouton Actualiser pour trouver votre contrôleur. le le contrôleur doit apparaître dans le menu déroulant de la à droite du bouton Actualiser pour continuer. Les contrôleurs Cosmic Color Pixie sont configurés via une fenêtre pop-up accessible depuis le LOR Onglet Contrôle. Tout d'abord, cliquez sur l'onglet Contrôle LOR, puis cliquez sur le bouton Config en bas de la fenêtre vous verrez la fenêtre suivante sur jp5 il n'y avait pas de cavalier quand j'ai recu la carte quel est l emplacement exat pour mettre le cavalier sur j3 pour passer a 100 leds Hello I come back to you I think that to pass my strings to 100 leds I am also wrong These riders will replace those parameters adjustable by Hardware Utility. Jumper 1 is closest to the end labeled JP5. Jumper What he does J1 WS28118, BRG, 50 pixels J2 WS2801, RGB, 50 pixels J3 WS28118, RGB, 100 pixels The hardware utility is used to configure the power on controller configuration. Parameters configured below, only logical resolution / failover state can be changed on the fly in sequences, and only in CCR compatibility mode. All the others the parameters are defined by and can only be changed by the hardware utility. Click the Refresh button to find your controller. the the controller should appear in the drop-down menu of the to the right of the Refresh button to continue. Cosmic Color Pixie controllers are configured via a pop-up window accessible from the LOR Control tab. First, click on the LOR Control tab, then click on the Config button at the bottom of the window you will see the following window on jp5 there was no jumper when I received the card what is the exat location to put the jumper on j3 to switch to 100 leds Link to comment Share on other sites More sharing options...
Recommended Posts