Ralphie Posted December 9, 2017 Share Posted December 9, 2017 Good morning all: I am running this purchased sequence on the latest LOR software for 16 CCR on a PIXIE 16D - V2. Clicking on the .lms file launches the LOR Sequence Editor v4.3.24 Pro. When I click "play" nothing happens on my tree except for a couple of pixels at the base of channel one flickering. Everything else is dead. Any help would be greatly appreciate. Link to comment Share on other sites More sharing options...
dibblejr Posted December 9, 2017 Share Posted December 9, 2017 Sounds like you haven't configured your pixie16. You have to copy paste their LMS into your channel config for your pixie unless you have the exact same config as HS. (highly doubted). Its just not plug and play. Find my thread entitled "Pixie Configuration Advice and Tips" for info. JR Link to comment Share on other sites More sharing options...
dibblejr Posted December 9, 2017 Share Posted December 9, 2017 Link to comment Share on other sites More sharing options...
Ralphie Posted December 9, 2017 Author Share Posted December 9, 2017 Thank dibblrjr for the information. What specifically are the steps for copying and pasting the LMS into your channel config for your pixie? Thank you. Link to comment Share on other sites More sharing options...
dibblejr Posted December 10, 2017 Share Posted December 10, 2017 10 hours ago, Ralphie said: Thank dibblrjr for the information. What specifically are the steps for copying and pasting the LMS into your channel config for your pixie? Thank you. First you have to configure the pixie. What other controllers are you running? What are their model #'s and Unit ID's? We will start there. PM me a # and a good time to call. Depending on your computer skilz may take 30 mins depending on what else you have. If your pixie is all wont take long. I'm pretty busy, mother natures snow storm wiped out my mega tree (star) for the 2nd time in less than a week. This is AL went from 80 to 20 in 2 days. We will have 4 seasons in 4 days. But I will attempt to call you while I work on props. JR Link to comment Share on other sites More sharing options...
movieman4 Posted December 10, 2017 Share Posted December 10, 2017 just open the sequence in the sequence editor. than tools/channel configuration. here you see the channels , you must put the correct network , unit and circuit matching your pixie 16. Link to comment Share on other sites More sharing options...
dibblejr Posted December 10, 2017 Share Posted December 10, 2017 (edited) 1 hour ago, movieman4 said: just open the sequence in the sequence editor. than tools/channel configuration. here you see the channels , you must put the correct network , unit and circuit matching your pixie 16. I think there’s a little more to it than that! You can set that as you mention all day long but until you configure it in HU it still won’t work. You also fail to mention dip switch settings where applicable along with figuring out what other controllers are at play. While that may be useful or not to someone that understands their way around LOR the OP may not be as advanced as you. BTW- circuits actually do not come in play while setting up the pixies it assigns 16 consecutive unit IDs. All the OP has to do is “properly” select the first unit ID. JR Edited December 10, 2017 by dibblejr Link to comment Share on other sites More sharing options...
movieman4 Posted December 11, 2017 Share Posted December 11, 2017 o yes sorry , i assumed the HU was already done and the pixie16 has his unit ID already. Link to comment Share on other sites More sharing options...
Ralphie Posted December 12, 2017 Author Share Posted December 12, 2017 JR: When I launch my sequence from Holiday Sequences.com and open the Channel Configuration option, I get the following. Link to comment Share on other sites More sharing options...
dibblejr Posted December 12, 2017 Share Posted December 12, 2017 We need to configure your pixie for you. That is HS configuration. Its to late tonight, I tried to call you earlier but got your VM and left message. You should have my # on CID. Shoot me a text before calling me anytime after 8 am tomorrow. Just to ensure I am avail. If you only have the one controller and you have everything ready it wont take long. JR Link to comment Share on other sites More sharing options...
dibblejr Posted December 13, 2017 Share Posted December 13, 2017 The OP is up and running now. Thank you for the screen shot it saved whats left of my hair. JR Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now