micheleboato Posted January 7, 2015 Share Posted January 7, 2015 Hi allI'm very happy because i finished to build the kit CTB16DV6 Blue Board :)It's very easy with lor manual!!! Thank you! So, i need your help :-)....beacuse....I don t understand again how to use j0 and s1 Could you help me and comment my status led if....0 CASEConnect to AC PowerLed offs0 0s1 1j0 without jumperThe voltage was ok on component------------------1 CASES0 FFS1 FFJ0 Without JumperThe Led in Output blink on sequence ok!-------------------2 CASES0 0S1 1J0 Without Jumper-Led off-I tried to connected USB485B can't find deviceI tried to refresh on hardware utility but without success-------------------3 CASELed blink and USB485B can't find device with:J0 without jumperS0 & S1 on 0I tried to refresh on hardware utility but without success-----------4 CASELed blink but USB485B can't find device with:J0 on Input LedS0 & S1 on 0I tried to refresh on hardware utility but without success-----------5 CASELed fixed and USB485B find device with:J0 on Input LedS0 on 0S1 on 1I tried to refresh on hardware utility with success, i tried to turn on the light with success-----------So, i have the deluxe kit and i don t understand how to use the J0 and what is the correct positionfor s0 and s1 when i use 16 channel with 2 ac power connectedWhat is the correct first step with deluxe kit for create a first sequence?Is it correct my case?ThxMichele Link to comment Share on other sites More sharing options...
wbaker4 Posted January 7, 2015 Share Posted January 7, 2015 Nothing on J0 (empty) S0 and S1 - Valid Unit ID values are 01 to F0 (1 to 240decimal.) 00 is not a valid Unit ID. The LED blinks when it is not connected to the 485 adapter. The LED stays on when the Controller has been found and is communicating. Link to comment Share on other sites More sharing options...
micheleboato Posted January 8, 2015 Author Share Posted January 8, 2015 Now:J0 always Empty------------- S0=0S1=0LAN Cat5 not connectedLed Blink fast -------------S0=1S1=1 led offLAN connected but software found 0 unit-------------S0=0S1=1 led offsoftware found 0 unit------------- In all case i have the output light the blink one So I repeat with1- J0 on Input led and S0,S1 to 0 and i found the devices with led on fixed, but the sequence editor not working2- J0 on Input led and S0,S1 to 0 and i found the devices with led on fixed, but the sequence editor not working with:Go to the Set Unit IDsection of windowUnderOld Unit IDselectAny UnitUnderNew Unit IDselect01ClickChange Unit IDbutton Link to comment Share on other sites More sharing options...
micheleboato Posted January 8, 2015 Author Share Posted January 8, 2015 I don t know how..but now i have Found 1 Unit - 01 - CTB16D Ver 4.32without jumper and s0=1 s1=1 But when i open LOR sequence editor i have under right red button comm port status : error Link to comment Share on other sites More sharing options...
micheleboato Posted January 10, 2015 Author Share Posted January 10, 2015 Hi,now working fine :-) Thank youMichele Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now