Jump to content
Light-O-Rama Forums

Purchased sequences - 'Not looking right' on CCR's


Recommended Posts

Posted

Hi all -

I'm a first year LOR user that dove in the deep end after seeing Brian's CCR's last year. - So I'm starting with 12 CCR's and 4 channel star in addition to 4 x 16 LOR 1602 controllers.

I purchased 4 sequences from superstarlights.com. - The sequences look perfect on screen in SuperStar, but it looks like 1 or 2 ribbons are 'off' during the songs. As an example, text is not readable, ribbons 1 and 7 seem to be slow, get 'stuck' or behave erratically - The ribbons all test fine in the hardware utility. - I have tested using a slower song like Silent Night and it's better but not perfect.

I am running 3 total networks - Regular via a USB485 for the 4 1602's, and a pair of USB485B's 1 for Aux A for CCR controllers 06-0B, and 1 Aux B for CCR controllers 0C-11. - My only problem was that I only had 2 USB ports on my laptop which forced the use of a hub. - To try to fix this, I'm presently building a new LOR system on a laptop with 3 USB ports... I am also confident that the Aux A/Aux B networks are appropriately assigned to COM2 and COM3 while the Regular network is on COM1.

I keep worrying that by following the steps in the manual for testing ribbons - I've messed something up in the hardware utility (I had one ribbon get set to resolution of 1, but I fixed that) - Can anyone confirm what the right CCR Config Screen settings should be ? - Or is this a red herring ?

I've done all the SuperStar channel configurations and they map fine through the export to the sequence editor.

Thanks in advance for any advice you can offer !

-David

Posted

The most common cause of "erratic" ribbons is if they are configured in "Legacy" mode, they need to be in "normal" mode. There is a video tutorial on configuration. Go to www.lightorama.com and click on "support" at the top, then click on "video tutorials". The SuperStar tutorials are at the bottom. Look for the one titled "SuperStar CCR Configuration". The part that covers the actual configuration is at 8 minutes into the video.

Also, in the Sequence Editor, click on the Edit menu, then Preferences, then Network Preferences. Make sure the CCR networks are set to "short range faster" or else they will lag.

I am told that using a USB hub should work, but I have not personally tried it. If it was me, I would do what you are doing and use a computer with at least 3 USB ports.

Posted

Thanks so much Brian - My controllers out of the box defaulted to 'Legacy' mode (and Standalone speed 9). - I actually tried to withdraw this post late last night as I found you'd answered a similar question a while back elsewhere in the forum. After making that change as well as increasing the speed on my 3 networks - WOW! That fixed the ribbons straight away...

I do have one minor thing still eluding me -- After I export from SuperStar into Sequence Editor, I want to apply my channel config so that I can add fill in lights on the house and bushes while the CCR's "dance". The channel config applies fine, and it doesn't mess up anything with any of the ribbons or the star -- but I do get lots of 'mirrored' patterns on the new/additional channels brought in from my channel import. - They seem to be copies of one CCR channel applied across 12 or so 1602 house light channels. - It isn't hard to just delete these rows entirely, but is there a reason why they are popping up at all ?

Posted

It sounds like the channels you are copying are larger than the area where you are pasting them. There is a "pop out" panel that appears when you hover the mouse over the left side of the Sequence Editor. In that panel are some "Paste Modes", be sure "Paste by Time" is selected.

Next, check that the number of rows of CCR channels you are copying is the same as the number of rows you have in your main sequence where you are pasting.

Posted (edited)

Appreciate the reply Brian - I've spent a good solid afternoon trying to resolve my channel import/export issue without any luck...I'm not actually copying/pasting anything. I'm just trying to apply my channel config/layout with the purchased SuperStar sequences.

Is your recommendation that instead of just changing the channel config,, I should create new/blank sequences - then copy and paste the data from the sequence created by the superstar export ?

I will try that tonight...

As for what I was trying to do originally Let me try to describe my steps a bit clearer...

  1. I open the downloaded sequence archives in SuperStar
  2. I reconfigure the channels to be spread across my 3 networks, assigning one of my controller for the 4 channel star (controller 5) and 12 CCRs (controllers 06-11)
  3. I assign the audio track
  4. Save as new File and Export to Sequence Editor

I now give the sequence a test play in Sequence Editor and everything is great.... But none of my house lights are on. To do that I'll need to expand beyond the default archive channel config of 1 LOR controller and 12 CCR controllers. I have exported a 48 channel configuration (channel names and colors) from a very basic sequence (all channels on) - no ramps/fades/etc. that I made by adding the additional controllers/channels to a purchased sequence. . You can view my Channel Config here,, by manually scanning the contents - I am comfortable that there is no sequence/song data in it - just channel configs : https://www.dropbox.com/s/v7661avn0h6h65k/David%27s%20CCR%20Tree%20and%20Controllers-Dec-5-2012-8pm.lcc

  1. In Sequence Editor - I open my newly created .LMS that I just played in a test and know it's good
  2. I do an Edit --> Export/Import Channel Configuration --> Import Channel Configuration in Sequence Editor
  3. I browse to my .LCC (file link above)
  4. Following the import - I get light data all over channels that weren't used before, and lost data from the original CCR channels - See screen grab here: https://www.dropbox.com/s/39i0emashifpsa6/CorruptSequenceGrab.jpg

I'm really bummed I can't figure this out. - If I could get my channel config into the purchased sequences, I could do a lot more with tying in the rest of the house with the CCR feature.

Again - my most sincere thanks for the assistance!

-David

Edited by dstafford
Posted

Sounds like the exported files from SuperStar play to your CCRs just fine. Your problem is combining the CCR sequence with your main sequence that controls your other lights. Importing a channel configuration file will not work. There are two ways to get the CCR sequence into your main sequence. You can add the CCR sequence as a subsequence to your main sequence or you can use copy/paste to copy the sequence from the CCR sequence into your main sequence. Doing a subsequence is easier, but some people report synchronization problems and so I recommend doing copy/paste.

There is a video tutorial on getting ccr sequences into your main sequence. Go to www.lightorama.com and click on "support" at the top, then click on "video tutorials". The SuperStar tutorials are at the bottom. Look for the one titled "Getting Superstar Sequences into Main Sequences".

Posted

Got it! Thank you again for your kindness and patience - I'm embarrassed yet again for having jumped in without investing the time to watch ALL the how-to videos first!

A nice side effect of copying and pasting the sequences in is that the timing and patterns on the star make for very nice copy/paste lines into other things like windows & bushes. - Very happy with how the 1st of 4 just turned out, can't wait to try it on the gear tomorrow!

All the best-

David

Posted

Good! Glad you got it to work.

Posted

Brian are there any 8 CCR's sequences to view. As I am new to all this. I was hopeing to purchase one. All I have seen were 12 CCR's or 6 CCR's.

Posted

Sorry, I have no sequences designed specifically for 8 CCRs. I have at least one customer with 8 CCRs that bought the 6 CCR sequences and just uses the middle 6 CCRs, they use all 8 in other sequences that they do themselves.

Posted

Good news first -- Doing copy/paste completely and quickly resolved my channel config issues. - I thought I could just overwrite channel names of an exported SuperStar sequence, but as the videos show - there are simpler/easier way to achieve that.

Follow-up question : - Are timing tracks available for purchased sequences ? I'd like to use the same ones as the CCR's for my master display sequence.

Posted

Sorry, no timing tracks, and there currently is no way to export the timing marks.

If you are writing a sequence on your other lights from scratch, the intended way is to make a visualization of you whole display, including the CCRs and import the visualization and then sequence your other lights from within superstar. Then your whole sequence is in superstar and when you export you don't have to combine things anymore. But almost noone is doing it because everyone is used to sequencing their other lights in the sequence editor.

For example:

1) make visualization of all lights including CCRs

2) open a purchase sequence

3) import visualization

4) save the file to a new name, this file will contain the purchased sequence and the visualization

5) sequence your other lights

6) save file again

7) export and play to your lights

Posted

Brian, Thank you for the reply. Today I weather proofed a heavy gauge plastic container and insulated the flooring. Used 3/4" plywood for a motherboard, mounting my 8 CCR controllers. (I also saved room to add 4 more CCR's next year. Everything is connected properly, I think. I have 3 dedicated lines with RS485's for each plugged into a Powerized multi-port strip. All 8 botten red lights are lit.

I cannot follow the hardware directions to get the blue light to signal. Is there a step by step tutorial on line that I can see?

Any help will be greatly appreciated...........Thanks

  • 3 years later...
Posted

Is there a individual located close to South Jersey that does house calls for my system. And if so what are the fees.   I have not been able to run my ccr's.  And after the first two years my eels won't work.  There is no obstruction between the controllers.  so the last 3 years I ran cat cable.    Any help or reply will be greatly appreciated.   I am not that electronic savy.  Although I am good repeating what I see done.

Posted

I don't live near South Jersey but I should be able to get things working for you. Do the CCRs light up at all?

I can set up a time and remote into your computer and make sure you have them configured properly. What is a good day and time for you?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...