Papa6058 Posted November 28, 2012 Share Posted November 28, 2012 I set all controllers IDs, tested them, then plugged a few lights to each and try to run show and I get this. Any ideas?http://img.photobucket.com/albums/v170/Corvette_Sooner/Errorstartingshow.jpg Link to comment Share on other sites More sharing options...
Don Posted November 28, 2012 Share Posted November 28, 2012 Make sure all other LOR programs are closed when trying to enable the schedule. Only one of them can take control of the com port at any given time.If you have no other LOR programs open, you will need to go into the Hardware Utility and make sure your com port settings are correctly set. Link to comment Share on other sites More sharing options...
Papa6058 Posted November 28, 2012 Author Share Posted November 28, 2012 Make sure all other LOR programs are closed when trying to enable the schedule. Only one of them can take control of the com port at any given time.If you have no other LOR programs open, you will need to go into the Hardware Utility and make sure your com port settings are correctly set.TY will try those now. Link to comment Share on other sites More sharing options...
Papa6058 Posted November 28, 2012 Author Share Posted November 28, 2012 Only other program I have used was Hardware Utility and I get this when I even try to open it:http://img.photobucket.com/albums/v170/Corvette_Sooner/stillerror.png Link to comment Share on other sites More sharing options...
Don Posted November 28, 2012 Share Posted November 28, 2012 You have a problem with the com port settings for your USB485.Did you load the USB drivers?Do you have the USB connected to your computer?Try the "Auto Configure" button in the HWU. That might locate the device. Link to comment Share on other sites More sharing options...
Papa6058 Posted November 28, 2012 Author Share Posted November 28, 2012 You have a problem with the com port settings for your USB485.Did you load the USB drivers?Do you have the USB connected to your computer?Try the "Auto Configure" button in the HWU. That might locate the device.I did load drivers before I ever connected the USB, USB is connected I did the auto configure when setting unit IDs all units worked when tested on COM Port 8I will try to auto configure again if that doesn't work I am going to reboot my computer and unplug and replug controllers Link to comment Share on other sites More sharing options...
Papa6058 Posted November 28, 2012 Author Share Posted November 28, 2012 Can you use Hardware Utility while all 3 controllers are connected gotts run take daughter to hospital Link to comment Share on other sites More sharing options...
Guest wbottomley Posted November 28, 2012 Share Posted November 28, 2012 Two LOR programs cannot control the same port at the same time. That means close one of them. Link to comment Share on other sites More sharing options...
Papa6058 Posted November 28, 2012 Author Share Posted November 28, 2012 You have a problem with the com port settings for your USB485.Did you load the USB drivers?Do you have the USB connected to your computer?Try the "Auto Configure" button in the HWU. That might locate the device.At hospital waiting room, so can't work on it now TY for your help Link to comment Share on other sites More sharing options...
Papa6058 Posted November 28, 2012 Author Share Posted November 28, 2012 There was only one LOR program running, and I did load the driver before I used the usb adapter. I read all paperwork and instructions and followed them best I could Link to comment Share on other sites More sharing options...
evan.a Posted November 28, 2012 Share Posted November 28, 2012 (edited) As I too am a father, take care of your daughter first.... Edited November 28, 2012 by evan.a 1 Link to comment Share on other sites More sharing options...
Papa6058 Posted November 28, 2012 Author Share Posted November 28, 2012 As I too am a father, take care of your daughter first....WE did. BTW Daughter is 33 and it was a bad migraine all is OKI shut down system and unplugged all controllers when we left, now everything works, port must have just crashed Link to comment Share on other sites More sharing options...
Recommended Posts