Suderer Posted November 7, 2012 Share Posted November 7, 2012 Hallo everybodyI am new in LOR and want to do all my lights with dmx.I bought a Enttec USB Pro interface and i think i do all like its here postet in the forum or shown on videos.but it does not work :-(i connect my pc with an usb cable to the enttec and from there with a five pin xlr to my controllers.In the network prefrences in LOR there is shown the enttec adapter and the enttec dmx pro protocolthe com listener is running and connection is acceptedwith the Enttec test program its possible to control my lights , but with LOR s3 its not i dont know whats to do that it will worki hope anyone can give me helpbest wishes from AustriaSudi Link to comment Share on other sites More sharing options...
Suderer Posted November 7, 2012 Author Share Posted November 7, 2012 its doneit was the wrong com port now it seems to work wellregards sudi Link to comment Share on other sites More sharing options...
bdeditch Posted November 8, 2012 Share Posted November 8, 2012 That seem to be the issue for a lot of people, if you have any other problems LMK. I have helped a few fix it. Link to comment Share on other sites More sharing options...
jeffro Posted November 25, 2012 Share Posted November 25, 2012 This is happening with my setup as well. I've checked everything but I must be overlooking something. I can control my DMX flood lights with the Enttec Pro test utility. From LOR S3, the lights do nothing.This is my first go-around with DMX -- is there a simple punchlist of config to verify? Link to comment Share on other sites More sharing options...
Dennis Cherry Posted November 25, 2012 Share Posted November 25, 2012 Post your network configurations for both the LOR and DMX settings. Link to comment Share on other sites More sharing options...
jeffro Posted November 25, 2012 Share Posted November 25, 2012 Post your network configurations for both the LOR and DMX settings.LOR: CTB16-PC, connected over COM5 (using USB485 adapter)DMX: adapter EN118359, with ENTTEC DMX USB Pro protocol (using Enttec DMX USB Pro)DMX adapter is connected over USB, with 5-pin XLR to RJ45 CAT5 adapter connected to RGB flood lights. Using the test utility that comes with the DMX controller, I can independently control the RGB flood lights as expected.In LOR S3, LOR network is identified as COM5 and DMX Universe is enabled as Universe 1. DMX listener port set to 8837.Opening the LOR control panel, LOR starts listening on port 8837 and the EN118359 adapter is identified and opened.Controlling the lights and running from LOR S3......nothing. :-(Thanks for the help. Link to comment Share on other sites More sharing options...
Dennis Cherry Posted November 25, 2012 Share Posted November 25, 2012 In SE is the Control Lights checked under PLAY? Link to comment Share on other sites More sharing options...
jeffro Posted November 25, 2012 Share Posted November 25, 2012 In SE is the Control Lights checked under PLAY?Yes. Link to comment Share on other sites More sharing options...
jeffro Posted November 25, 2012 Share Posted November 25, 2012 Ok....now it works.Nothing has changed, but I applied several updates to Windows 7.I would *really* like to know what could have impacted this, because the configuration did not change from what I've described above, and the only changes made here were in updates to the OS. Link to comment Share on other sites More sharing options...
Rick Childers Posted November 29, 2012 Share Posted November 29, 2012 FYI, I was having similar problem, and this post had the answer ( http://forums.lightorama.com/index.php?/topic/20127-huge-annoyance/ ) .It is possible that you may not have had a 485 adapter plugged in. This drove me nuts Link to comment Share on other sites More sharing options...
viennaxmas Posted November 29, 2012 Share Posted November 29, 2012 I have had similar issues, especially when changing the USB port. Sometimes messing with the LOR network settings and changing the Universe to some other and back helped. I did not have a chance to track it down to a pattern... Can't wait for E1.31 next year... Link to comment Share on other sites More sharing options...
jerrymac Posted November 29, 2012 Share Posted November 29, 2012 I found that if you use the enttec utility to test lights you must unplug the enttec pro and the LOR usb adapter then plug them in again. It appears the the enttec utility does not release the port (?) when you exit the program, and the LOR usb adapter can not connect to the Enttec. Link to comment Share on other sites More sharing options...
Recommended Posts