Jump to content

Visualizer file for Holiday Coro - Singing Mrs Santa Claus Face


Donl1150
 Share

Recommended Posts

  • 2 weeks later...

You can create that in the vis using that picture for the background. It is super easy. If you cant get it and still want me to show you how to convert and sequence this 3 channel face I can help you with that after HAlloween

I have the Santam he may look dif that Mrs Santa but on the prop there is no dif in sequencing

JR

Link to comment
Share on other sites

Thanks JR.  I did create the viz file for Mrs. Claus using that pic.  My drawing isn't the greatest but it serves the purpose.  As for sequencing, I am doing fine with that on this prop since there are only 3 channels for her Open or Closed mouth.  Not too difficult.  Same is true for Mr. Claus singing.....only a couple of channels for Open or Closed mouth.

Now the Coro singing tree is different.  Lots of channel possibilities for Open / Closed.  It's here that Papagayo is useful.  I am currently working on a song with the tree in Papagayo (after finally figuring it out) but once done there, I still don't know how to use the Translator to get it from PPGO into the proper channels of the SE.  I could use help with that if you have time after Halloween.  Much appreciated if you could!  Thanks

Don

Link to comment
Share on other sites

10 hours ago, Donl1150 said:

Thanks JR.  I did create the viz file for Mrs. Claus using that pic.  My drawing isn't the greatest but it serves the purpose.  As for sequencing, I am doing fine with that on this prop since there are only 3 channels for her Open or Closed mouth.  Not too difficult.  Same is true for Mr. Claus singing.....only a couple of channels for Open or Closed mouth.

Now the Coro singing tree is different.  Lots of channel possibilities for Open / Closed.  It's here that Papagayo is useful.  I am currently working on a song with the tree in Papagayo (after finally figuring it out) but once done there, I still don't know how to use the Translator to get it from PPGO into the proper channels of the SE.  I could use help with that if you have time after Halloween.  Much appreciated if you could!  Thanks

Don

Bob will be your best bet there.

I wiped my brain of the pgo logic and only recall what it took to just get ready to sequence in papagayo. 
 

You have to select the clip board from what I recall and it will put your sequence how you configured it in the transfer tool that Bob created.

JR

  • Like 1
Link to comment
Share on other sites

6 minutes ago, ItsMeBobO said:

Download teamviewer and invite me (ItsMeBobO on teamviewer)  to control your PC and we can go over anything you want. 

Even MIIP? LOL JK for now. Ah- you were referring to the OP.

 I haven't advanced that far yet. Just pushed 1000 nodes today in my last 2 pumpkin faces. That's all 4 took a week. Gonna put them out today and perhaps tomorrow start placing the controllers.

Then on to adding MIIP to my ready to go 3 sequences. LOL

JR

Edited by dibblejr
Link to comment
Share on other sites

22 hours ago, ItsMeBobO said:

Download teamviewer and invite me (ItsMeBobO on teamviewer)  to control your PC and we can go over anything you want. 

Thanks for the offer but I'm not going to pay $49/mo for teamviewer.  I'll continue to try to figure out the translator.

 

 

Link to comment
Share on other sites

On 10/15/2020 at 5:07 PM, ItsMeBobO said:

Download teamviewer and invite me (ItsMeBobO on teamviewer)  to control your PC and we can go over anything you want. 

It was just pointed out to me that there is a free version for personal use.  I have now installed it and will try to figure out how to use it.  If you're available next week, I would have time either Wednesday or Thursday if that works for you Bob.  Let me know.  Thx!

Link to comment
Share on other sites

  • Don locked this topic
Guest
This topic is now closed to further replies.
 Share

×
×
  • Create New...