Jeffery m Posted December 7, 2017 Author Share Posted December 7, 2017 a phone call would have to wait til tommorow my phone broke today and I will be replacing it tommorow Link to comment Share on other sites More sharing options...
dibblejr Posted December 7, 2017 Share Posted December 7, 2017 Okay, so probably all gen 3 determined. Model and gen can be seen on the board itself. Just need to start all over, from your channel config/ network preference and then on to HU to fix you up. JR Link to comment Share on other sites More sharing options...
default Posted December 7, 2017 Share Posted December 7, 2017 8 minutes ago, greenie95125 said: One of the utilities that comes with the software is called Network Preferences. I can see a lot of info is being thrown at you, but what is being talked about with Network Preferences is this. I'll bow out of this conversation now, your in capable hands just wanted to show you a picture of Network Preferences. Alan... 1 Link to comment Share on other sites More sharing options...
Jeffery m Posted December 7, 2017 Author Share Posted December 7, 2017 my software is 4.3.18 advanced Link to comment Share on other sites More sharing options...
dibblejr Posted December 7, 2017 Share Posted December 7, 2017 Send me a copy of your "current channel config". Also open your network pref and write down what you see and send it as well. dibblejr@hotmail.com let me have a look JR Link to comment Share on other sites More sharing options...
dibblejr Posted December 7, 2017 Share Posted December 7, 2017 3 minutes ago, default said: I can see a lot of info is being thrown at you, but what is being talked about with Network Preferences is this. I'll bow out of this conversation now, your in capable hands just wanted to show you a picture of Network Preferences. Alan... Thanks Alan Link to comment Share on other sites More sharing options...
Jeffery m Posted December 7, 2017 Author Share Posted December 7, 2017 how do i get to network preferences Link to comment Share on other sites More sharing options...
Jeffery m Posted December 7, 2017 Author Share Posted December 7, 2017 ok sent thru dropbox net preferences said com3 57.6k for speed Link to comment Share on other sites More sharing options...
dibblejr Posted December 7, 2017 Share Posted December 7, 2017 (edited) 1- You have nothing input from unit 8 circuit /channel 8 Are you manually building these controllers in or are you opening SE and right click on a unit and "insert device" "above/ below"? That's the correct way So if you have 10 that's why you only see 8 That was a click glance JR Edited December 7, 2017 by dibblejr Link to comment Share on other sites More sharing options...
Jeffery m Posted December 7, 2017 Author Share Posted December 7, 2017 unit8 channel 8 says mini tree Link to comment Share on other sites More sharing options...
Jeffery m Posted December 7, 2017 Author Share Posted December 7, 2017 have not inserted device above or below which do I do Link to comment Share on other sites More sharing options...
dibblejr Posted December 7, 2017 Share Posted December 7, 2017 You have to finish building unit 8-10 to find 10 units. But you have not network pref or anything built into unit 8 circuit 8 -unit 10. You can put all the words you want for humans but the computer cannot comm with it. The correct way to add device Open SE Open a SEQ or MAster Config Right Click on a unit Select Insert Device above or below Select your ctb device set the LOR Reg network and unit ID Then just fill out the channel button JR Link to comment Share on other sites More sharing options...
Jeffery m Posted December 7, 2017 Author Share Posted December 7, 2017 when u say right click on a unit do u mean a channel Link to comment Share on other sites More sharing options...
dibblejr Posted December 7, 2017 Share Posted December 7, 2017 1 minute ago, Jeffery m said: have not inserted device above or below which do I do If I was you id start all over. Ive been there with a lot more channels. However You can try to start from 8 You should create a master config first Open SE Edit Export channel config Save it where you can find it Close what you got Now start by opening a new sequence and select that config from the folder instead of using the default 8 Now Delete unit 8 -10 Now right click on unit 7 and follow the steps above a couple posts JR Link to comment Share on other sites More sharing options...
dibblejr Posted December 7, 2017 Share Posted December 7, 2017 Also a little advice Group your channels per controller or system. Easier to scroll through and fix stuff later. There is a box to check when setting up conrollers as above. JR Link to comment Share on other sites More sharing options...
Jeffery m Posted December 7, 2017 Author Share Posted December 7, 2017 thank you I will try everything you said Link to comment Share on other sites More sharing options...
dibblejr Posted December 7, 2017 Share Posted December 7, 2017 2 minutes ago, Jeffery m said: when u say right click on a unit do u mean a channel Yes, a channel. Or unit if you group its much easier.Group while setting up, you can always group now. Example Right click on Unit 1 channel 1 and select add as group. Then you will select the channels ie 1-16 for unit 1 and ok. Now you have everything on that unit packed into 1 tab until you click the + button Link to comment Share on other sites More sharing options...
Jeffery m Posted December 7, 2017 Author Share Posted December 7, 2017 when I go to edit the only things thats highlighted to choose from are preferences set paste mode and undo settings Link to comment Share on other sites More sharing options...
dibblejr Posted December 7, 2017 Share Posted December 7, 2017 If you haven't done so already you can right click on unit 1.1 Hand rails. "Convert to group" you can name the group "hand rails" since that is what the 16 are. This will consolidate all 16 channels under that 1 button. Makes life much easier. I was trying to be fast with my replies so difficult to explain 100%. JR Link to comment Share on other sites More sharing options...
dibblejr Posted December 7, 2017 Share Posted December 7, 2017 If you have SE open with your sequence the edit tab next to file. Almost all the way down you should see Export/ import channel config Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now