Jump to content
Light-O-Rama Forums
Sign in to follow this  
DevMike

PixCon16 Minimum Configuration Checklist

Recommended Posts

Bare Minimum PixCon16 Setup Checklist


Be sure to follow each of these steps IN ORDER. Do not proceed to the following step until you are sure the current step is complete. Please note that you may be further along in your testing than where this check lists starts. Please do not skip any of the previous steps even if you think you have performed them correctly already. Start at #1.

If you have already tried to configure the board, you should first FACTORY RESET the PixCon16.  Instructions are provided in the manual.  These instructions assume that you have a 'stock' PixCon16 to start with.

Critical checkpoints points are in bold, but you may experience a problem at any step. If you are having problems at a checkpoint, check ALL steps up to this one to ensure they are completed properly.

The PixCon16 is a professional level board, and does require some in-depth knowledge about how E1.31 works, DMX and networking concepts.  You may need to consult other sources if you run into issues or do not understand a concept. 

If you do have an issue and if you think everything is good to that point, and you would like to contact us for help STOP. Do not go further and do NOT change any configuration. If you would like to experiment and try to resolve the issue, please do! We encourage you to find the solution on your own. However if in the end you must contact us, reset the board and start again at step 1 and then stop at the failing step and contact us. We rely on the board being in a known state at every step of this checklist to help you.

Please ensure that you have AT LEAST S4 V4.3.14 Or Higher to configure the board.  Some older versions may not be able to properly detect the Pixcon.
 
  • 1.  Pixels have a front and a back (IN and OUT). Ensure you know which side data goes IN to.  Pixels from LOR are plainly marked, or are correctly pre-wired.  if your pixels have an arrow, that arrow points AWAY from the board.
     
  • 2.  Pixels have a voltage. Ensure you have the proper power supply.  LOR Pixels are typically 5v or 12v.  If your pixel package from LOR included a power supply, you do not need to worry about this step.
     
  • 3.  Pixels have current draw (amperage). Ensure you are not exceeding the amps per channel/power supply/etc.  Pixels from LOR will draw 3A per 50 pixels at 5V (15 Watts), 3A per 100 pixels at 12V (36 Watts).  If you pixel package from LOR included a power supply, you do not need to worry about this step.
     
  • 4.  Wire power supply to PixCon16, if not already wired.
     
  • 5.  Remember – never connect or disconnect anything from PixCon16 with power applied.
     
  • 6.  Power up board. Follow instructions in DMX and E1.31 for pixel control document if needed (linked below). Open Network Preferences/Find Configure PixCon16/Click on PixCon16 in list, and open the PixCon16 configuration window.  

    Only work with a SINGLE PixCon16 connected to your network at one time until properly configured -- IP address conflicts can occur if you attempt to configure 2 or more.  

    Do not continue until you are able to reliably talk to the board and configure it.

    If you are having difficulty reliably talking to the board, read:

    http://www1.lightorama.com/PDF/IntroductionToDMXandE131.pdf
    Pay particular attention to page 8.

     
  • 7.  Ensure board firmware is AT LEAST 1.4.8. Do NOT downgrade if higher!  Downgrading a PixCon16 will brick the board requiring special software to recover!  All PixCon16s sold since late 2016 are at or above V1.4.8.  Do not continue until firmware is updated to at least 1.4.8. Instructions are found in the manual.  If you have the LOR Control Panel loaded, UNLOAD IT before attempting to update firmware. Updating the firmware while the Control Panel/Comm listener are running can cause the board to FAIL.
     
  • 8.  Properly set up Pixel Type and Pixel Speed in configuration. Ignore all other parameters.  LOR Pixels are WS2811.  Most are high-speed.
     
  • 9.  Properly wire 1 pixel string to a 4 wire connector. Follow pin-outs in the manual.   Note -- Some pixels do not have/require the clock signal.
     
  • 10.  Connect pixels to a single port, and power up. Pixels may briefly flash. Pixels that stay ON indicate incorrect pixel type or speed selected in #8.  For LOR Pixels, ensure that you selected 'High Speed'.  If High Speed does not work (it should in almost all cases), select slow speed.
     
  • 11.  Run hardware test on the pixels as documented in manual by using the buttons on the PixCon16.  If pixels do not work, problem is most likely #8. Go back there. 
    Do not continue until the Hardware Test works properly.
     
  • 12.  Wire the rest of your pixels to the 4 wire connectors. Connect them to the PixCon16. Run the hardware test (step 11) again. Ensure all pixels are working correctly. Pixels that are not working indicate a problem with the pixel itself, or an under-rated power supply.
    Do not continue until the Hardware Test works properly for ALL pixels.
     
  • 13.  Again bring the PixCon16 configuration up.  On the first tab of PixCon16 configuration, ensure you have the correct option specified for J3/J4. If you will use the board in ELOR mode, turn this option ON. For E1.31 ensure this option is OFF.  If you have not done so yet, install the drivers for the USB adapter and ensure the USB adapter is working properly.
     
  • 14.  On the Second tab set up each port of the PixCon16 properly. You can use simple mode or advanced mode. All options are documented in the help file for the software or in the manual for the PixCon16. Remember, for E1.31 universes must also be set up in Network Preferences (the software will offer to do it for you), for ELOR, 500K speed and Enhanced Light-O-Rama network (done in step 16). It is best to write down the settings.
     
  • 15.  Ensure you have the LOR Control Panel loaded (which will load the LOR COMM Listener).  The COMM Listener is ALWAYS required to control pixels.
     
  • 16.  Properly configure your network preferences.
    • E1.31: Ensure Universe matches universe on the board & Set IP address correctly (multicast or unicast/specify).  It is easiest to use multicast.
       
    • ELOR: Ensure the COM port is set to at least 500K and ELOR mode is turned ON.
       
  • 17.  E1.31: Do not disconnect anything. 
    • Both LEDs should be SOLID ON. 
      Do not continue until they are.  NOTE:  Your computer may need to be rebooted.  If you reboot go back to step 15.
       
    • ELOR: Disconnect Network cable, ensure jumpers on PixCon16 for J3/J4 are set to LOR. Connect HS USB adapter to computer, CAT5 from USB adapter to J4 of PixCon16.   NOTE:  You must have previously installed the drivers for the high speed USB adapter.  Use another non-PixCon16 unit to test if you are unsure the USB adapter is working properly.  
      Both LEDs should be SOLID ON. 
      Do not continue until they are.  NOTE: Your computer may need to be rebooted. If you reboot go back to step 15.
       
  • 18.  Start Hardware Utility. If asked if the HWU should take control of a port say NO. Open the pixel console. Set Pixel Console params correctly and test pixels with sliders.
     Do not continue until you can successfully control pixels.
     
  • 19.  Your board is now ready to use.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

×