Jump to content
Light-O-Rama Forums

Todd_91

Members
  • Content count

    38
  • Joined

  • Last visited

Community Reputation

0 Neutral

About Todd_91

  • Rank
    Member

Profile Information

  • Gender
    Male
  • Location
    Tinley Park, IL
  • Occupation
    Cabinet maker

More About Me

  • How I learned about Light-O-Rama -
    Internet
  • Favorite Decorating Holiday?
    Christmas

LOR Software

  • LOR Software Version
    3.11.2
  • License Level
    Advanced

Recent Profile Visitors

106 profile views
  1. E682 LOR S4 DMX Setup

    Wanted to get this out before I cannot remember what exactly I did to get the Sans Device to communicate with LOR E1.31 1) Find out E682 IP address (Read E682 instruction on how to find this out) 1A) Jumper J22 needs to activate for the set of outputs you will be using for the DMX or the lights will not work. 2) Set E682 Receive mode to Unicast (make sure to hit update system information) 3) Set test pattern to 0 (again update system) 4) Under which every output you will be using on the E682 set Output Type to DMX in my case I used outputs 1-1 to 1-4 choose the universe number again in my case I used universe 1 set start channel (hit update button at the end of this configuration line) (note all the above steps are done in the E682 webpage) (note all the sets below are done in LOR) 5) Load LOR control panel 6) Make sure shows are disabled or else lights will not work in Sequence editor (note if shows are disabled the tray icon for LOR will be red if it is blue shows are enabled) 7) Load Network Preferences 8) Under the DMX tab click Unv 1 and then the advance button 9) Select Use E1.31 10) Under IP Address select Specify and then enter in the IP address you obtained from step 1 11) Hit ok then apply 12) At this point if the sequence editor is open you need to close it down and restart to make sure the network information gets update. You should be able to then do some testing with a sequence to make sure all is good. I will be working on setup with the G3MP3 Director and ELOR when I get it figured out. If you have any questions I will try to help you as best I can, pretty new at this dmx stuff so still learning. Hope this helps. Todd
  2. Pink Floyd Money

    copy please todd_91@att.net Thanks,
  3. Looking for Minions jingle bells

    Copy please todd_91@att.net Thanks,
  4. Sounds of Silence by Disturbed

    Copy please todd_91@att.net Thank you
  5. Light 'em Up, Fall Out Boy

    Would like a copy todd_91@att.net Thanks,
  6. New Years Eves Rush

    Sure todd_91@att.net Thanks,
  7. New Year Eves Katy Perry

    Copy please todd_91@att.net Thanks,
  8. New Years Eves George Michael

    Yes please send to todd_91@att.net Thanks
  9. Seasonal Entertianment

    Z, I found out about a month ago that Seasonal went out of business sent him one email which got not response. Then proceed to dispute the charge with my credit card company and got all my money back. The charge on my account was from sometime in May so if you purchased with a credit card contact your card company and you should be good.
  10. RGB Spotlight

    Just found out that Seasonal Entertainment is out of business, and still owes me some product, so now I am looking for a replacement source for their Rainbow Spotlight. Does anyone know of a comparable product? Thanks.
  11. Song not matching lights

    Update: I started with the original purchase sequence then kept adding controllers until the sequence did not work properly. I found that if I left out 50 ccr blubs that the sequence worked fine. Any ideas? Thanks,
  12. Song not matching lights

    Yes actually named the song with Audacity in the title to make sure I was selecting the proper one.
  13. Song not matching lights

    Tried converting in Audacity multiple times but still not in sync. Went back to the original purchased sequence and it works fine. When I add in additional dmx fixtures gets out of sync. Found that if I only use 50 of my ccr bulbs instead of the full 100 set the sequence works fine. I am using a ELOR into two 24 channel dmx controllers along with 4 16 channel LOR controllers and the CCR bulbs are connected to the last controller.
  14. I have a sequences that was purchased from LOR which is a you can modify. After about fifteen seconds the lights start going fast than the song as it is playing so the lights end way before the song does. The song was convert to MP3 with Audacity 128kbps and bit rate mode set to constant the song was downloaded directly from amazon. I have attached the sequence file. Thanks for any help. Wizards_of_Winter.zip
  15. G3-MP3 Director Song not in sync

    How do I check if the songs are a constant bit rate?
×