Jump to content
Light-O-Rama Forums

Bevvyboy

Members
  • Content Count

    18
  • Joined

  • Last visited

Community Reputation

0 Neutral

About Bevvyboy

  • Rank
    New Forum User

Profile Information

  • Gender
    Male
  • Location
    United Kingdom
  • Occupation
    Fitter

More About Me

  • How I learned about Light-O-Rama -
    You tube
  • Favorite Decorating Holiday?
    Christmas

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Thanks Bill P Sent from my HTC One_M8 using Tapatalk
  2. Bill P Could I possibly have some leaping arch sequence as well please would be much appreciated thank you bev.clarke.bc33@gmail.com Sent from my HTC One_M8 using Tapatalk
  3. mpageler thanks didn't realise it is : bev.clarke.bc33@gmail.com To be honest anything Christmassy will do for a start this year Thanks for help so far bevvyboy Sent from my HTC One_M8 using Tapatalk
  4. Hi has anyone got any leaping arch sequences that they could share please Thanks Sent from my HTC One_M8 using Tapatalk
  5. Sorry for delay yes I can see that but still no response Sent from my HTC One_M8 using Tapatalk
  6. Hi would also like them if you would be kind enough Thank you bev.clarke.bc33@gmail.com Bevvyboy Sent from my HTC One_M8 using Tapatalk bev.clarke.bc33@gmail.com
  7. Thanks K6ccc Still no good but will try and post some screen shots , as I don't seem to be able to select the RS 485 it doesn't seem to find it ,have I set something else by mistake ? As no adaptor is found Thanks again for your help Sent from my HTC One_M8 using Tapatalk
  8. Hi guys I have an Lor 16 channel setup and I am using a 27 channel DMX board to run talking faces (total of 16dmx channels) I have programmed the sequence in the sequence editor and viewing the animation it works reasonably well (will need a few more tweaks on the lip sync), I have made the faces and the lights all work on the DMX test dip sw. I have a Lor dongle and made the crossover cable and I can tell the Dmx controller is receiving the signal as the green light is blinking My problem is that when I run the sequence Nothing happens, but all of the lights come on stay on , how do I get them to follow the sequence like on the LOR (animation) What am I not doing right in setting this up ? What do I need to start / load / check to make it run Any help would be fantastic as I am now looking at just a normal controlled Christmas lighting (no show) until next year as I am now bald from pulling out my hair Please if any of you know what I need to do could you walk me through it Thanks for any help suggested / offered Cheers B.boy Sent from my HTC One_M8 using Tapatalk
  9. I have a 16 channel Lor and I have a 30way rgb dmx board which I have connected to rgb ribbons to create a tree Can I drive the rgb board from the Lor controller to produce various sequences ? I'm sorry if I sound a bit thick but I am very new to any of this , so you're help would be much appreciated thanks Sent from my HTC One_M8 using Tapatalk
  10. Dennis Laff and DevMike Thanks for your help I checked out the hyperlink and worked through it only to find that, the Transformer is supplied by the group 9 - 16 and I had only put power on 1 - 8 Now sorted and up and running Thanks again
  11. Hi Guys I am a newby that has just built the 16 channel DIY kit, I have plugged it in (mains) switched on and no Setup Light came on, I have power at the hot and neutral contacts, Full Voltage, both ends of the fuses were also tested to neutral Hopefully one of you good guys will have some ideas as to why it doesn't want to power up? and because of this the port on the computer cannot find a consul to assign Help Urgently required please
×
×
  • Create New...