Jump to content
Light-O-Rama Forums


  • Content Count

  • Joined

  • Last visited

Everything posted by Bad-Magic

  1. Posted this on planet christmas but lack of replies atm. Well i just went out to the shop and all they had left was multifunctional minis. Since they are multifunctional and i'm thinking of purchasing LOR i need to know which wires i cut off from the multi box and solder together so it isn't stuffing up during a show.. http://img112.imageshack.us/img112/6848/img1618ud9.jpg
  2. How much would it cost to air mail two CTB-16D boards to australia? I would send a direct email to LOR but tried a few months ago for another thing and didn't get a response. Hope someone can help me out here. Cheers.
  3. Jeff Millard wrote: Ahh, i was going to get the ctb16d, so it's best to wait for the blue ones to come out? Hopefully they will be out before the sale.
  4. Thanks Geoff, so if i have a 3 minute song and then 5 minutes to cool down is this fine? Denny, thanks for that.
  5. I haven't bought it yet but you could always put it on your own CD or memory stick instead of paying for a disk. But if you are wondering if you need the CD and download to run it, the answer is one or the other.
  6. Brilliant Geoff i was hoping for you to reply So i shouldn't worry about overheating if i don't switch on and off at 0.3+? Thanks!
  7. Geoff, read your post in the Aussie light o rama users place "Hi Andrew & Salli I too had this concern last year and had been warned by Dan (LOR) that there had been transformer failures from switching and dimming." you said that 10 mins of on/off were fine then a break was good. do you mean a break as in turning everything off or just on or what and for how long? Thankyou
  8. Geoff Harvey wrote: Hi, so you do use the transformers that come with the lights? don't they get hot after switching lots, that is what i'm getting worried about. How do you get around this?
  9. levelbest wrote: Where did you get it from?
  10. Wow thanks for the help denny! So you are saying make sure you get proper extension cords that can carry 15-20 amps? but for the extension cords that go to the lights that won't matter very much? so i also will get sent an email asking wether i want to get the board changed over to 240V for Australia?
  11. Bad-Magic wrote: Thanks danny, is anyone able to answer this?
  12. I downloaded and installed the sequence editor but get the following error message:@ http://img162.imageshack.us/my.php?image=errorqn6.png i'm trying this on a laptop that is a little less than a year old, i tried rebooting but still get that error message. Does that mean it can't finda com port on my computer? because i don't have one. i will have to buy the usb connecter.
  13. I had a look at the it might be a better option for me since it weighs less and i can put the cords i need in myself. I read the guide and it is very good the pictures help alot (now i know where you plug in the channels) my only question is Where does the the power source for the board go? i know that you use 2 for the lights but i'm not sure about the board. Could i use any old extension cords and cut the ends off and attach them to the Unit or do you require special ones(i'm talking about the cords that go out of the controller and the lights plug into them) ? ok one more question i promise For the cords that plug into the controller do they need to be special or can i use extension cords for them aswell? Thanks.
  14. Thanks for the replys guys! Dan, I would get them during the sale when you apparently get free shipping i would say.
  15. Bad-Magic

    The Sale

    Might cost more for me since i'm in Australia.
  16. Bad-Magic

    The Sale

    How much is shipping usually for say a 16 chan showtime product?
  17. Bad-Magic

    The Sale

    If i decide to buy some controllers, i will defintalely buy them in the sale, how much money do you save in the sales is there a rough amount? say 10% or something?
  18. Hi, I'm from Perth, Western Australia. I am very interested in purchasing a http://store.lightorama.com/ba16chpa.html (16 channel starter pack) When i added it to cart it said that you don't ship it to Australia?? I will need to change all the plugs over to Australian ones and under stand that i will have to make a change to a "jumper" board and change the settings to 240V - is this correct? Are there any instructions on how to change the setting over? Will i need to replace any of the cords that come with this or will just changing the ends of the plugs work fine? Thanks.
  • Create New...