• Announcements

    • LORAdmin

      S5 Beta Comments   07/16/2017

      Please keep all comments about S5 in the Open Beta General Comments section. This will help the developers by only have to look in one area of the forums for comments/questions/concerns about S5.

rmturner54

Members
  • Content count

    251
  • Joined

  • Last visited

Community Reputation

1 Neutral

About rmturner54

  • Rank
    Member

Profile Information

  • Gender
    Male
  • Location
    Waxahachie, Texas
  • Occupation
    Electrician

Contact Methods

  • Yahoo
    rmturner54@sbcglobal.net

More About Me

  • How I learned about Light-O-Rama -
    Internet research
  • Favorite Decorating Holiday?
    Christmas

LOR Software

  • License Level
    Advanced
  1. Just an update. Replaced 2 mosfets, channel 4 and 7. Board now 100% again Sent from my SM-G930P using Tapatalk
  2. I run a static show after my normal show for security. I cant help you with triggers Sent from my SM-G930P using Tapatalk
  3. My bad i said from lor...i co tacted the help desk at lor to get pn Sent from my SM-G930P using Tapatalk
  4. Yes i did. This is straight from lor. Sent from my SM-G930P using Tapatalk
  5. This is from LOR Hi Richard, We don't stock the triacs for the CMB16D DC controller. You can purchase them from Mouser: http://www.mouser.com/ProductDetail/Fairchild-Semiconductor/FQPF30N06L Regards, Mike WowLights Productions Sent from my SM-G930P using Tapatalk
  6. I got a reply from the help desk with correct Mouser PN. I will post the info this evening Sent from my SM-G930P using Tapatalk
  7. Revisted rgb#3 issue. No wiring errors. No issue except red channel 7 still stays on. Still looking for mosfet pn Sent from my SM-G930P using Tapatalk
  8. What is a good part number for the mosfets. i should order some
  9. Ok...i will revisit issue tomorrow Sent from my SM-G930P using Tapatalk
  10. During testing from HW utility the other day, my power supply burned up. Ordered and installed new one. This was my original PS of 6 years +. So I wrote off the failure to age of PS. After installing new one, I discovered several of my RGB floods were terminated backwards, reversed + and -, so corrected my wiring mistakes and tested from the HWU. RGB #1 ch 1,2,3, worked perfect. RGB #2 ch 4,5,6 not so good. ch 4 stays on, ch 5 and 6 works ok. RGB #3 ch 7,8,9 same as RGB #2. Disconnected ch 4 and 7. Retested RGB #2 and #3. Results as follows: RGB #2, ch 5 and 6 still work ok. RGB #3 nothing works on it until I re hookup ch4, then ch 5 and 6 starts working again. I suspect some shorted mosfets. Any ideas?
  11. Yea i do need to upgrafe and will wait till xmas is done Sent from my SM-G930P using Tapatalk
  12. Never thought to look at it. Thank you so much. Now all i need is a new 12v ps. Sent from my SM-G930P using Tapatalk
  13. One thing i saw on the staus log was, the static seq played then tried to play a seq i use for after show. To my stupid surprise i had this after show seq in my show scheduler. I removed the after show seg from the show editor. All is well agai Sent from my SM-G930P using Tapatalk
  14. Ok Sent from my SM-G930P using Tapatalk
  15. The llop at end in seq editor will stay checked then when i close editor and open seq again, its unchecked Sent from my SM-G930P using Tapatalk